Tag Archives: rims

FJ40 OEM Wheel Restoration – Wire Cup Brush or Sandblasting?

If you’re looking to restore your original FJ40 wheels you may be wondering to use a wire cup brush or media blasting. In a recent blog post, I showed you how to use a 3″ wire cup brush and an angle grinder to clean up your rims. After four hours and two wire cup brushes (which cost $30 total) I wasn’t happy with the results the wire cup brushes gave us. I decided to take my rims over to Dennis Salisbury at C&D Painting and Sandblasting in Ellicott, Colorado (just outside Calhan).

Dennis is your man when it comes to sandblasting or media blasting anything. He had my rims taken care of in 15 minutes. If you’re in the Colorado Springs area and ever need anything media blasted (frame, tub, doors, chest hair…) give Dennis a buzz at (719) 683-4819.

Pictures of the FJ40 Wheels in Their Original Condition

FJ40-Wheel-Rim-Restoration5419

FJ40-Wheel-Rim-Restoration5420

FJ40-Wheel-Rim-Restoration5421

FJ40-Wheel-Rim-Restoration5422

FJ40-Wheel-Rim-Restoration5430

FJ40-Wheel-Rim-Restoration5428
Pictures of the FJ40 Rims After Cleaning With a Wire Cup Brush

FJ40 Wheel

FJ40 Wheel

FJ40 Rims

FJ40 Rims
Pictures of FJ40 Wheels After Media Blasting

FJ40-Wheel-Rim-Restoration5592

FJ40-Wheel-Rim-Restoration5591

FJ40-Wheel-Rim-Restoration5589

FJ40-Wheel-Rim-Restoration5588

FJ40-Wheel-Rim-Restoration5583

Angle Grinder With Wire Cup Brush FJ40

FJ40 OEM Wheel / Rim Restoration – Using a Wire Cup Brush

I’m working on restoring a 1975 Toyota Land Cruiser FJ40. It’s an early 75, so it has drum brakes all around (and thus drum-style wheels). There are a couple different ways to go about restoring these rims. I could have them sandblasted (aka media blasted), which would cost around $100-150. Since I’m on a budget, I decided to go the wire cup brush route. I found a Milwaukee 3″ wire cup brush that screws on to my angle grinder at Home Depot for around $19. It was more than I wanted to spend, but cheaper than having them sand blasted. (NOTE: In the end, I did have them sand blasted. Check out this post about that process.)

STEP 1: Prep

There are some projects where you can cheat and go without protection. This project isn’t one of them (as you’ll see in an image further down the page). Eye protection is critical, so DO NOT run that angle grinder with the wire cup brush without proper eye protection. I also wore a dust mask, as the rust that gets kicked into the air was pretty thick and nasty. To keep myself from going deaf, I also threw on some ear protection (which was a good idea because this process can take several hours).

FJ40-Wheel-Rim-Restoration5418

Step 2: Prepare Working Area

Find a good place with plenty of space to work. It was freezing here in Colorado when I was working on these rims, so I did it in my garage on my work bench. If the weather is decent, I’d recommend doing this project outside where the dust and debris can go wherever it pleases and you’ll have less to clean up.

Here are a few pics of my wheels before I started the restoration process.


FJ40-Wheel-Rim-Restoration5420

FJ40-Wheel-Rim-Restoration5428


FJ40-Wheel-Rim-Restoration5421
FJ40-Wheel-Rim-Restoration5422

FJ40-Wheel-Rim-Restoration5430

FJ40-Wheel-Rim-Restoration5431

FJ40-Wheel-Rim-Restoration5432

Step 3: Attach Wire Cup Brush to Angle Grinder

Screw on your wire cup brush and make sure it’s nice and tight. I used a crescent wrench (while pressing in the spindle lock on my angle grinder) to make sure it was nice and snug. You don’t want this thing coming off at 11,000 RPM.

FJ40-Wheel-Rim-Restoration5424

Step 4: Go To Town

You can see in this pic I’m only wearing one glove. That was only because I was managing the camera to take the pics. Be sure to wear two gloves. As you begin the process of stripping down the rims with the wire brush, little pieces of metal fly all over the place. I had several go through my gloves and poke me pretty good. When I went to shower off, I took off my shirt and found two pieces sticking into my flesh. Those little suckers go flying like crazy, so make sure you’re hands are protected.

Hold the angle grinder tight with both hands, especially when you get around to working near the clips. Don’t hit the clips with the brush. Instead, use sandpaper and hit those by hand. I learned my lesson the hard way when one of my clips broke off because the wire brush is just too powerful and snapped it right off.
     FJ40-Wheel-Rim-Restoration5435

Start with the edges.

FJ40-Wheel-Rim-Restoration5437

After tearing down the front, backs and edges of two and half rims, my Milwaukee 3″ wire cup brush pretty much gave it up as there were hardly any wires left. Towards the end of the life of this wire brush, more and more wires were flying off faster and faster because there weren’t as many wires compacted together to hold them in.

FJ40-Wheel-Rim-Restoration5425

FJ40-Wheel-Rim-Restoration5445

FJ40-Wheel-Rim-Restoration5442

As $20 was steep enough for one wire cup brush, I worked a bit harder to find one a bit cheaper. I found another flavor of the 3″ wire cup brush at my local O’Reilly’s Auto Parts store for $13.

FJ40-Wheel-Rim-Restoration5438
FJ40-Wheel-Rim-Restoration5440
FJ40-Wheel-Rim-Restoration5441

I continued on with the new wire brush, but unfortunately (and is usually the case) the cheaper wire brush was…well…cheap. It didn’t last nearly as long as the Milwaukee wire cup brush. It was enough to finish the job, but next time I’ll spring for the better quality wire brush.

Below you can see some of the wires that came off the cheaper brush en-masse piled up on the inside of the rim.
FJ40-Wheel-Rim-Restoration5446
  FJ40-Wheel-Rim-Restoration5448

This wire brush wire hit a little too close to home…

FJ40-Wheel-Rim-Restoration5466
FJ40-Wheel-Rim-Restoration5467

Step 5: Finished

As you can see, the wire cup brush did an okay job cleaning up the rims. I couldn’t get in very close where the clips were and in a couple other areas.

FJ40 Wheel

FJ40 Rims

FJ40 Rims

At the end of the day I decided to go ahead and media blast these. Below is a video documenting that process.